Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across West Hollywood
A broken gate in West Hollywood usually means one of three things: a rusted hinge post, a failed operator board, or a gate that’s sagged out of alignment. Most repairs run $180 – $480 depending on what’s actually wrong, and since we’re based right in Hollywood, we can typically reach any West Hollywood address the same day you call. Salt air off the Atlantic, saturated summer ground, and 1950s-era hardware all play a role in what fails here, and we’ve seen every variation. Call (866) 665-5592 for a straight answer and a free estimate before any work begins.
Why Carter Gate Repair Is West Hollywood’s Preferred Gate Repair Company
West Hollywood isn’t a separate island. It’s a tight grid of canal-front homes, ranch houses off Taft Street, and small-lot properties where a stuck gate blocks the whole driveway. We know that when a gate won’t open at 7 a.m., you’re not shopping for options – you’re looking for someone who can get there and fix it. Our Gate Repair team has been working this corridor long enough to recognize the exact failure patterns: rust through hinge plates, saturated footings, and automation that was installed a decade ago and never touched since.
Homeowners in West Hollywood call us because we’re gate specialists, not generalists. Every service we offer – repair, electric gate repair, installation – lives inside the gate category. That’s the whole trade. Our technicians work on at least nine operator brands and aren’t tied to selling you any one of them. If your Viking operator has a dead control board, we replace the board. If a DoorKing swing arm is grinding, we diagnose it on the spot. We work on the gate you have.
Directed by Mitch Delvecchio, Carter Gate Repair has built its reputation in West Hollywood one working gate at a time. Residents see the same crews on the same streets, and that familiarity matters when a storm has just come through and everyone’s gate is acting up on the same morning.
Styles & brands we work with
Driveway Gate Repair in West Hollywood
Driveway Gate Repair in West Hollywood has a very specific character, because the housing stock here works against gate hardware. Most homes were built between the 1950s and 1970s, and a significant share sit on canals where moving a vehicle in and out depends on a single gate working. It’s not decorative. When a driveway gate on a small West Hollywood lot sags or fails to latch, you can’t park securely, and on canal-front properties a broken gate can leave the rear of the house exposed to water access.
Driveway gate repairs in West Hollywood typically run $190 – $520. The low end covers hinge replacement and realignment on a standard single swing gate. The high end covers re-setting a hinge post in fresh concrete, repairing a cracked weld, or replacing a bent section of frame. We quote the full price before any work starts, and the quote you approve is the price you pay.
Hinge and Post Replacement
This is the most common driveway gate repair we perform in West Hollywood. Salt air rusts hinge hardware until the gate drags on the ground, and that friction eventually stresses the operator motor. We replace the hinges and, where needed, the post itself.
Operator Repair and Diagnostics
When the gate is structurally sound but won’t open or close, the problem is usually in the operator – a bad capacitor, a failed limit switch, a control board that’s given up. Since we service LiftMaster, FAAC, BFT, Linear, and more, we diagnose by direct experience, not by reading a manual for the first time on your driveway. That includes LiftMaster repair in West Hollywood done from real field knowledge.
Gate Welding in West Hollywood
Gate Welding in West Hollywood is frequently the difference between repairing a gate and replacing it entirely. Wrought-iron gates from the original canal-housing era are often solid enough to be worth saving, but the welds at corners and hinge mounts crack after decades of salt air and heat. A cracked upper corner weld on a swing gate lets the whole frame flex, which throws off the latch alignment and makes the gate look neglected. We weld those cracks, reinforce the weak points, and the gate goes back to square.
Welding work on West Hollywood gates typically runs $150 – $400 depending on the number of cracks and the access to the work area. That’s a fraction of a full replacement, which is why we’ll always tell you if a gate is salvageable before we suggest anything else. Your gate back on track – without replacing what doesn’t need replacing.
Weld Crack Repair
A hairline crack at a weld joint eventually becomes a full separation, especially when a gate takes storm-force wind loads. We grind the area clean, weld it solid, and often add a reinforcing plate where the original design was underbuilt for South Florida wind.
Rust-Thru Section Replacement
On many older West Hollywood gates, the lower rail and hinge-mount areas rust through from the inside. We cut out the failed section and weld in a new steel section, then re-coat it to match the gate. The repaired gate is as strong as it was when installed, sometimes stronger.
Trusted Brands We Service in West Hollywood
Our Gate Repair in West Hollywood customers have every kind of operator and gate hardware imaginable, and we work on all of it. LiftMaster and Linear show up most often on residential swing and slide gates. FAAC and BFT appear on higher-end installations and some small commercial properties. Viking and DoorKing run the light-commercial side. We carry common replacement parts for these systems on our trucks, so a West Hollywood repair doesn’t have to wait on a parts order when a control board fails. Nine brands. One specialty.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Repair Problems We See in West Hollywood Homes
- Rusted-through hinge plates on canal-front gates. The salt-laden ocean air just a few miles east means hinges and latch plates on West Hollywood canal-front gates rust through years earlier than in inland Broward. By the time a gate sags, the hinge plate is usually the culprit.
- Leaning or failed hinge posts after heavy rain. Saturated ground after summer thunderstorms weakens post footings. On older canal-front properties where the original footings were shallow, a storm can leave the hinge post leaning and the gate dragging.
- Operator failure after lightning or power surges. West Hollywood’s near-daily summer thunderstorms send surge events through gate operator boards. We see dead transformers and fried control boards more often than mechanical motor failures here.
- Post-storm wind damage and impact-code repairs. High winds bend frames and tear loose hardware, and some gates need anchoring upgrades to meet current hurricane standards. We inspect the whole system after a storm, not just the part that’s visibly broken.
Pricing for Gate Repair in West Hollywood, FL
Here’s what you can expect to pay in West Hollywood, based on the work we actually see in this market:
- Hinge replacement and realignment: $180 – $320 per gate section
- Weld crack repair: $150 – $300 per crack, depending on access and prep
- Hinge post reset in fresh concrete: $280 – $520 including excavation and concrete
- Operator control board replacement: $280 – $680 depending on brand and board type
- Full operator replacement (labor and unit): $850 – $2,200 depending on capacity and features
The exact price depends on the gate’s size, weight, and what the repair actually requires. We quote it clearly and in writing before any work starts. Nothing is billed that wasn’t approved. Call (866) 665-5592 for a free estimate – we’ll come out, look at the gate, and tell you what it needs.
We Also Serve Cities Near West Hollywood
Beyond West Hollywood itself, our crews regularly cover Hollywood, Andover, Carver Ranches, and Miramar. If you’re a property manager handling multiple sites across the Hollywood – Broward corridor, we can often schedule several addresses in a single visit.
Serving West Hollywood, FL — Our Local Coverage Area
We’re based in the West Hollywood area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in West Hollywood
West Hollywood sits just a few miles from the Atlantic, and the same salt-laden air that corrodes boat trailers and outdoor hardware works on gate hinges every day of the year. Canal-front properties get the worst of it, because the water is right there, and the air moving off the canals carries salt constantly. Standard steel hinges on a canal-front West Hollywood gate can rust through in eight to twelve years, while inland Broward gates often see fifteen or more. We keep stainless steel hinge replacements and penetrating oil on the truck as routine stock for exactly this reason. If your gate is starting to sag, call (866) 665-5592 before the post itself fails.
Every automatic gate operator has a manual release mechanism, usually a keyed cylinder or a pull-handle located on or near the operator housing. On most LiftMaster, FAAC, and Viking residential operators in West Hollywood, you insert the key, turn it a quarter turn, and the operator disengages from the drive so the gate can be pushed open by hand. After power returns, re-engage the release and run the operator through a full cycle to confirm it’s back in sync. If you can’t find the release or the gate won’t re-engage, call us at (866) 665-5592 rather than forcing it – a forced re-engagement can strip the gear.
A sagging gate after a storm usually means the hinge post footing got saturated and the post shifted, or the storm’s wind load cracked a weld that was already fatigued from years of salt-air corrosion. In West Hollywood’s older canal-front homes, many original footings were poured shallow by today’s standards, and once the ground saturates, they lose grip. The gate then drops a few inches, drags at the latch side, and starts binding against its own stop. We fix it by re-setting the post or re-welding the frame – no need to replace the whole gate. For a diagnosis and free estimate, call (866) 665-5592.
Yes. Automatic gate operators in West Hollywood, like everywhere in Florida, must have functioning entrapment protection – typically photo-eye sensors, reversing edges, or both – that stop and reverse the gate if something is in the path. These systems are not optional, and they’re designed to prevent serious injury, especially to children. If your gate doesn’t reverse when it meets resistance, stop using it immediately and call us at (866) 665-5592. This is a safety repair we take seriously, and we’ll get it corrected the first visit.
Yes, we repair both. On older wrought-iron gates, the work is typically hinge replacement, weld repair, and post reinforcement. On newer aluminum gates, the common failures are different – usually the operator, the control board, or a welded aluminum joint that’s cracked from wind flex. We’re brand-agnostic and material-agnostic. The gate you have is the gate we fix. Call (866) 665-5592 for a free estimate on any gate repair in West Hollywood.
On a canal-front lot off Taft Street, our crew repaired a 1970s wrought-iron swing gate whose hinge post had rusted through at the concrete footing, causing the gate to sag and drag. We replaced the hinge post with a galvanized steel post set in fresh concrete, swapped the rusted hinges for stainless steel, applied penetrating oil to the latch and hinges, and then recalibrated the LiftMaster operator to correct the swing path. The gate now opens smoothly, and the homeowner has a maintenance schedule to keep the next salt-air corrosion cycle from becoming another emergency.
If your gate is sagging, grinding, stuck, or simply not responding, don’t wait for the next storm to make it worse. Call Carter Gate Repair at (866) 665-5592 for a free estimate. We’ll get your West Hollywood gate back on track – without replacing what doesn’t need replacing.
Written by Mitch Delvecchio, Owner at Carter Gate Repair, serving West Hollywood and the surrounding Hollywood – Broward corridor.