Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Hollywood?
Gate repair in Hollywood, FL typically runs $150 to $650 for most residential fixes, with the average call landing around $275. Simple adjustments like a misaligned hinge or a worn roller often stay under $200, while electric gate repair involving control boards, loop detectors, or operator replacement pushes $400 to $1,200 or more. Commercial high-cycle operators and underground wiring faults are the main reasons a bill climbs past $1,500.
We’re gate repair specialists, not a garage-door company that handles gates on the side. That matters on pricing: we diagnose the control board, the operator, and the hardware together because failures usually connect. If you want a real number for your gate, call us at (866) 665-5592 for a free estimate in Hollywood. Estimates are free and upfront pricing is our default.
Gate Repair Cost Breakdown (2026)
Here’s what the line items actually look like across Hollywood, from the beachside condos off Ocean Drive to the gated communities out near I-95. Ranges below reflect what we see on real jobs in 2026, not national averages.
| Repair Type | Typical Cost (Hollywood, FL) | What’s Included |
|---|---|---|
| Service call & diagnostic | $75 – $125 | On-site inspection, troubleshooting, written findings (often waived when you approve the repair) |
| Hinge, roller, or track adjustment | $125 – $200 | Realignment, hardware tightening, lubrication |
| Sagging or dropped gate realignment | $175 – $350 | Post adjustment, hinge replacement, welding where needed |
| Operator/opener repair (residential) | $250 – $600 | Motor, control board diagnostics, limit switch, or gear replacement |
| Safety edge or loop detector replacement | $200 – $450 | Photo-eye, safety edge, or in-ground loop sensor replacement |
| Control board replacement | $300 – $700 | Board swap, reprogramming, testing cycle |
| Full operator replacement (residential) | $700 – $1,400 | New LiftMaster, FAAC, or Linear operator, labor, wiring check |
| Commercial/high-cycle operator repair | $500 – $1,200 | DoorKing or Elite operator service, heavy-duty component replacement |
| Underground wiring fault repair | $400 – $1,500+ | Trenching, conduit work, low-voltage rewire |
| Gate arm / boom gate repair | $200 – $500 | Arm replacement, spring tension, cabinet repair |
What drives the number up: electrical faults (underground wiring is Hollywood’s nemesis – more on that below), commercial-grade operators, and gates built into older concrete or masonry columns where anchoring a new hinge means real drilling work. What keeps it down: addressing a small alignment problem before it becomes a hinge that fails completely and a gate that sags into the ground. Our gate repair in Hollywood page covers the full scope of what we fix. If you already know something is wrong, call (866) 665-5592 and we’ll give you a real range before anyone shows up.
What Affects Gate Repair Pricing in Hollywood
Hollywood isn’t Miami or Fort Lauderdale, but it has its own quirks that shape the bill. Here are the factors that move the price most.
- Salt air and humidity. Properties east of US-1, especially near Hollywood Beach and the Intracoastal, deal with constant salt in the air. It corrodes hinges, strikes, and control board terminals faster than inland gates ever do. We see hinges seize up in three years that would last eight or nine in the western parts of Hollywood near Emerald Hills or Cooper City. Corrosion repair adds labor because freeing rusted hardware takes time.
- Storm season and standing water. Summer thunderstorms saturate the ground, and South Florida’s flat terrain means water pools right where the operator sits. We routinely see loop detector failures and control board water damage after heavy rain in July and August. Underground wiring faults spike in those months.
- Gate type and material. A swing gate on a residential driveway is a different job than a slide gate or a boom gate at a commercial plaza. Wrought iron and aluminum gates on masonry columns generally cost more to repair than a simple chain-link swing gate because hardware is heavier.
- Operator brand and age. We work on nine brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – and we know each brand’s weak points. Older units and discontinued models can cost more because a specific part has to be sourced. Brands with accessible parts keep the bill lower.
- Residential vs. commercial. A high-cycle DoorKing operator on a commercial entrance runs cycles all day. Those repairs cost more because the components are heavier and the operator is built to run hard. Residential repairs on a Mighty Mule or Ghost Controls typically stay lower.
- Access-control and safety systems. If your gate has keypads, intercom entry, vehicle detectors, or safety edges, any fault multiplies the diagnostic work. These systems are where an inexperienced technician stalls. We do electric gate repair in Hollywood as a named specialty for exactly this reason.
If you’re still deciding who to call, it helps to understand the difference. Many companies handle gates as a sideline to garage doors or fencing. We do only gates, so diagnosis comes faster and the recommendation is honest – we don’t have a garage door or a fence to sell you instead. We work on the gate you have.
How to Save on Gate Repair
Nobody likes surprise repair bills, especially after a storm. Here’s what actually helps in Hollywood, based on what we see on service calls.
- Get it checked before small problems get expensive. A gate that drags or sticks slightly is often a $150 to $200 alignment job. Let it go for a few months and it turns into a bent hinge, a failed operator, or a gate that scrapes the pavement – and the bill doubles or triples.
- Clear the track and check your sensors yourself. A surprising number of “broken gates” are just debris on the track or a photo-eye blocked by a leaf, a cobweb, or a branch. That’s a free fix before you call anyone.
- Address corrosion early. If you’re near the beach, have hinges lubricated and checked each year. A little prevention stops the rust-repair upcharge later.
- Ask for a repair first, not a replacement. A good technician should tell you whether your operator has life left in it. Our whole approach is your gate back on track – without replacing what doesn’t need replacing.
- Take advantage of free estimates. A phone call costs nothing. We’ll give you a clear range before a technician shows up, and our upfront pricing means no surprises. Call (866) 665-5592.
One honest note: if a gate is genuinely on its last legs, repairing a broken operator again and again can cost more over time than a new one. We’ll tell you the truth either way, because we only do gates and we don’t have a dealer conflict pushing us toward a sale. If you’re considering a fresh start, our gate installation in Hollywood page lays out what a new system involves, and the home page shows our full range of services.
FAQs – Gate Repair Cost
How much does the cheapest gate repair cost in Hollywood?
The lowest-cost gate repair in Hollywood is usually a hinge, roller, or track adjustment, running $125 to $200. A basic diagnostic often runs $75 to $125, and that fee is frequently applied to the repair when you approve it. Call (866) 665-5592 for an exact quote – estimates are free.
Is it cheaper to repair or replace a gate operator?
Repair is almost always cheaper in the short term, with a residential operator repair running $250 to $600 versus $700 to $1,400 for replacement. Replacement wins only when the operator is near the end of its life or parts are hard to source. We’ll tell you which one makes sense for your specific model, and our free estimate covers both options.
How much does electric gate repair cost in Hollywood?
Electric gate repair in Hollywood typically costs $300 to $700 for control board or sensor work, and $700 to $1,400 if the operator needs full replacement. Underground wiring faults can push higher, sometimes $400 to $1,500 or more depending on trenching. These jobs need a specialist because the electrical side is where generalists stall. Call (866) 665-5592 for a quote.
Can you come today?
Availability depends on our schedule, and we won’t promise same-day unless we can actually deliver – but a free estimate call today is always possible at (866) 665-5592. We’ll give you a real window and a clear price range before anyone heads out.
Why is gate repair in Hollywood sometimes more expensive than other Florida cities?
Salt air near the beach and storm-season water intrusion both add labor and parts. Coastal Hollywood gates near the Intracoastal corrode faster, and summer storms drive up electrical and loop-detector repairs, so the same job can run $50 to $200 higher here than inland. Call (866) 665-5592 and we’ll price it for your address.
Get a Straight Answer on Your Gate
If your gate is acting up, call (866) 665-5592 for a free estimate. We work on the gate you already have – swing, slide, boom, or high-cycle commercial – and we know the operators inside out, from LiftMaster and FAAC to DoorKing and Mighty Mule. Whether you’re in a condo off the beach, a home in Emerald Hills, or managing a commercial lot along the coast, our specialist team will diagnose the real cause, give you an upfront range, and repair what makes sense to repair. Free estimates, upfront pricing, and no replacement you don’t need. Estimates are free – reach out and we’ll get your gate back on track.
Pricing reflects the Hollywood market as of 2026. Carter Gate Repair offers free estimates – call (866) 665-5592.
What Our Customers Say
"Repair is holding. He was quite a bit later than the window I was given, and the office didn't call me about it, I had to call them. The work itself was done well once he got here."
— Lisa Anderson"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
— Brooke Miller"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
— Rachel Reed